English French German Italian Portuguese Russian Spanish

Chris Lemke’s HMS Bounty Community Build Project

When the S.i.B.B.A. Facebook and YahooGroup(s) decided on a community build of the HMS Bounty as a memorial to her sinking. I was very excited, she’s a lovely ship, and I decided to take this opportunity to build my first ‘large’ SiB.

Bounty Project.jpg

My project would be scaled to fit into a 2 gallon jug, measuring twelve inches long, six inches around, with a one inch opening at the neck.  This makes my waterline model of the HMS Bounty 7.5” long from stern to the tip of the Bowsprit, 1.25” wide, and 5.25” from the waterline to the tip of the Main mast.  In this picture I’ve glued the blueprint to the sides of the hull block halves.

Bounty Project 001.jpg

The hull blocks were drilled and had pins added to hold the halves together, then using a thin razor saw I cut across the hull down to the deck level.

Bounty Project 002.jpg

With the lines cut you can then carefully break away the scrap wood leaving you with the blocks carved roughly down to deck level.

Bounty Project 003.jpg

Then it’s just a matter of sanding the deck surface nice and smooth.

Bounty Project 004.jpg

Next I cut even ½ inch sections from some very thin bass wood stock for the deck planks.

Bounty Project 005.jpg

With a lot of planks cut I began laying and gluing the deck planks to the hull blocks, making sure to lay the planking in a staggered pattern.

Bounty Project 006.jpg

One side of the hull planked. Also here you can see the pins that hold the hull halves together.

Bounty Project 007.jpg

The deck is laid, I now let the glue dry for a full 24 hours before sanding the deck smooth.

Bounty Project 008.jpg Bounty Project 009.jpg

Using a fine razor saw I then cut out the shape if the hull as viewed from the top, you must be very patient with this step to make sure you don’t splinter your deck planks. The Deck is the sanded smooth.

Bounty Project 010.jpg Bounty Project 011.jpg

Using the schematics of the hull I then carved and sanded the lower hull into to proper contours.

Bounty Project 012.jpg

Next the Forefoot, gunwales and the area the stern castle windows will go are added.For this I used sheet styrene. Close attention was paid to how the hull halves will fit together.To accomplish this the stern gunwale and window ‘plate’ is attached only to the starboard hull side and cut to fit snugly onto the port side when the hulls are together.
 
Bounty project 013.jpg
 
Well the project is moving right along...
 
The next step was to build and paint all the deck details, these were built from a combination styrene, brass rod, and basswood… the helm is made from the fly-cog of a wrist watch. Again special attention is made to make sure that the hulls can easily be separated and put back together without damaging any of the details. Now onto the cannons.
 
Bounty Project 017.jpg Bounty Project 018.jpg
Bounty Project 019.jpg Bounty Project 020.jpg 
Bounty Project 021.jpg Bounty Project 022.jpg
Bounty Project 023.jpg Bounty Project 024.jpg
 
New progress pics on the HMS Bounty...
 
I used 1mm brass tubing and filed it into a proper cannon shape thinning the tubing as close to a proper diameter as I could.
 
Bounty Project 041.jpg

The gun carriages were carved from small blocks of bass wood.
 
Bounty Project 042.jpg

Painting the barrels.
 
Bounty Project 043.jpg
 
Mounting the cannon onto their carriages and finishing paint.
 
Bounty Project 044.jpg

 

 Stowing the cannons in place on the deck.

Bounty Project 045.jpg

View thorough the gun ports.
 
Bounty Project 046.jpg

 

 

New Bottles

Bottle 1425 - Cow Boat in a Bottle
Bottle 1424 - Double Crane in a Bottle
Bottle 1420 - La Belle Pouf in a Bottle
Bottle 1419 - Cat on a Chair in a Bottle

New Articles

 Only 5 most recent Bottles/Articles displayed.  Click on "New Items" in the menu above for all new site content.